August 2022 – The Quintessential Clothes Pen

In March 2022, I had another fitting on the pair of stays I started posting about recently. I tried a few different things and some seemed to work. It gave me hope!

I decided to add tape straps to these stays, partly to help counteract the back pulling away from my shoulder blades and slouching in towards center. This method of straps comes this pair of stays at the McCord Museum (accession number M969X.26), which is dated 1785-1790.

The idea has intrigued me for awhile and specifically appeals for this project because I didn’t like the fit and feel of the attached fabric straps and had already cannibalized them to make gussets, anyway.

Adding the tape helped the stays feel better, but the gussets were still a problem. I decided to move the gussets up higher by about 3″. I didn’t have quite enough fabric length to do that but I decided to piece on additional sections at the bottom. Piecing is completely period and seemed like a better idea than not having stays that I could wear!

Additionally, I maxed out the seam allowance on both sides of the gussets and the abutting pieces. I’m hoping those things will help narrow the back gap. I’ll also add a new boning channel in the gusset.

In terms of fit, the side view actually isn’t bad with the added strap!

The tape shoulder straps wrap across the back and then will hook in the front. For the fitting the test strap is just safety pinned. Other pins are marking where the strap hits as well as the finished length of the tabs.

After this fitting, the to do list includes:

resetting/piecing the gussets and adding boning channels and boning to them
whipping the edges of the stays in preparation for binding them
binding the edges of the stays
adding the tape straps for a final fitting

I’ve been very busy, so those things are moving along quite slowly. I did update the gussets and start whipping the edges, so there is some progress.

That’s all for now. Next post, I’m going to go back to the early construction details of these stays.

The Beginnings, The Abbreviated Version

The very late 18th century (1780s and 1790s) is a mostly new period for me. I have a chemise… but no other underclothes that fit, no dresses, and quite likely no accessories… I’m starting mostly from scratch! And as one does (or at least as I do) when faced with a new period, I decided to make completely hand sewn stays as the foundation. That was in 2018!

I thought I had a grand plan. I was so excited about my stays! I tried a new way of patterning, tried a new method of stiffening my fabric, sewed oodles of boning channels by hand, shoved bones into all the channels that were just a little too tight, put in my eyelets by hand… And I documented all of it to share it here.

Catching Up To The Current State Of Things

Then in mid-2021, I did a fitting… and realized that I was really unhappy with the stays. Really unhappy. Mostly due to the fit.

The stays pushed my tummy downwards so it rounded out underneath the front point and tabs, but, even worse, the back pushed down on my lower back and was super uncomfortable! AHHHHH! After all that time spent hand sewing! And it’s not like I jumped right in to hand sewing stays without mockups and thinking that the pattern fit. No, I’d done those steps and hadn’t noticed anything wrong! GRRRR.

My immediate reaction was to put the project away. I just couldn’t bear it. After I calmed down (weeks later, mind you!), I tried to see what I could do to fix the issues. I decided to add a gusset into the back, since the pressure seemed partly to come from the bottom of the lacing gap being quite wide. I had only very small scraps left, so the only way to do this was to cannibalize my straps (which is fine, because I wasn’t super keen on them restricting my shoulders, anyway).

Here’s a photo of the back of the stays with the triangular gusset already added (and some other things that I’ll talk about later). The gap at the bottom was even wider before I added the gussets!

Fast forward a bit more and I had another fitting. The gusset helped a little, but I still had pressure on my lower back. And… the front problem, I realized, was due to a combination of the front being too short for my frame and this idea I had to use ⅛” bones, to mimic the size of originals…

I’ve had success with plastic zip ties as bones, so I thought I could use narrow ones to create the width I was looking for (I used these, purchased on Amazon). Unfortunately, they were very tight in the channels. It took a lot out of my wrists to cut and push in all the bones. The width of the zip ties looks great, but they’re too flimsy. Look how much I can bend back the front tab!

After much deliberation that included going back to look at the original that the pattern I used is based off of, and the reproduction made from it that is in the book I used, I realized that the original stays are just really short in the front. AHHHHH! (More about the book I used will be coming in a future post.)

I didn’t process this earlier, in any of my fittings, or my mockup, or my patterning, or my looking at the book! And I’m incredibly low on fabric! Below are my scraps, minus the long ones in the center, which were already used to face the eyelets.

So… I was left with a half finished pair of stays that took many, many hours to even get to this point–wonderfully sewn in terms of methods, but which I couldn’t wear. I was very upset and put the stays into time-out (again!).

I’ll stop the story of the stays here and continue on with my updates from the most recent fitting next time.